Here is proof that the grid leak drip pans can overflow.
Fossil
EDIT: Forgot to mention as I was on the phone while composing this....it is directly in back of a 10kw FM rig. The roof leak developed about 4 inches in back of the rear door.
I THINK IT IS TRYING TO TELL ME SOMETHING
- Deep Thought
- Posts: 3411
- Joined: Thu Mar 20, 2008 9:23 am
- Location: La Grange, IL
- Contact:
Re: I THINK IT IS TRYING TO TELL ME SOMETHING



I was at a site "up nort" that had a bucket full of ice melter sitting in the corner. It had attracted so much moisture from the air that it filled the bucket about 3" deep and proceded to eat its way out of the bottom, leaving a nice salty (and surprisingly slippery) little puddle on the concrete floor.

Mark Mueller • Mueller Broadcast Design • La Grange, IL • http://www.muellerbroadcastdesign.com
- kkiddkkidd
- Posts: 753
- Joined: Mon Dec 03, 2007 11:13 am
- Location: Lawrenceburg, TN
Re: I THINK IT IS TRYING TO TELL ME SOMETHING
I was greeted with this little gem a couple of weeks ago at a new to me client. Some genius decided it was a good idea to penetrate the roof of a mil surplus commo container to get the coax directly down into the TX. It had been leaking for quite some time as evidenced by the rusty screws and corrosion to the AL top plate.
The amazing thing was that very little water actually penetrated the interior of the Elenos TX due to it sitting a bit off plumb and most of the water running off the top and down the back panels...
https://youtu.be/SG6NTrn2YXo
A liberal application of silicon sealer/adhesive on the bottom temporarily stopped the flow and the next day, a liberal application of "Through The Roof" sealant hopefully will keep it dry until a rubber roof can be installed.
I just found Through the Roof at a local Lowes. It appears to be just a jar of clear acetic acid (extremely strong vinegar smell) type silicon sealer/adhesive but it seemed to stick easily to the roof and boot surfaces even though they were pretty wet.
Now, to find a roofing contractor that doesn't want $5k to put a rubber roof on an 8x12 aluminum box....
Later,
The amazing thing was that very little water actually penetrated the interior of the Elenos TX due to it sitting a bit off plumb and most of the water running off the top and down the back panels...
https://youtu.be/SG6NTrn2YXo
A liberal application of silicon sealer/adhesive on the bottom temporarily stopped the flow and the next day, a liberal application of "Through The Roof" sealant hopefully will keep it dry until a rubber roof can be installed.
I just found Through the Roof at a local Lowes. It appears to be just a jar of clear acetic acid (extremely strong vinegar smell) type silicon sealer/adhesive but it seemed to stick easily to the roof and boot surfaces even though they were pretty wet.
Now, to find a roofing contractor that doesn't want $5k to put a rubber roof on an 8x12 aluminum box....
Later,
--
Kevin C. Kidd CSRE/AMD
WD4RAT
AM Ground Systems Company
http://www.amgroundsystems.com
KK Broadcast Engineering
http://www.kkbc.com
Kevin C. Kidd CSRE/AMD
WD4RAT
AM Ground Systems Company
http://www.amgroundsystems.com
KK Broadcast Engineering
http://www.kkbc.com
Re: I THINK IT IS TRYING TO TELL ME SOMETHING
The video shows the craziness...wow. Is there any hope of getting the line rerouted?
- kkiddkkidd
- Posts: 753
- Joined: Mon Dec 03, 2007 11:13 am
- Location: Lawrenceburg, TN
Re: I THINK IT IS TRYING TO TELL ME SOMETHING
At some point in the future... Yes. There are numerous side wall access ports in the container that would have worked great but I assume that the installer didn't want to fool around with (or have) elbows and/or rigid components. Not to mention that the walls are no more than 1/4in soft AL plate but they cut thru a 1/2in hardened AL roof plate as well as the 1/4in roof panel below that to come straight down into the coax port. The current installation pretty much precludes bypassing the main TX with an exciter feeding a Type-N to 1-5/8in adapter. The coax can't be picked up off of the top of the tx...
This and it's sister site are fun to work on.... Anything I do is an improvement. I understand that both sites were built with mostly volunteer labor so they probably aren't too bad considering.
These are a pair of those "boy do I have a story" sites.
Later,
--
Kevin C. Kidd CSRE/AMD
WD4RAT
AM Ground Systems Company
http://www.amgroundsystems.com
KK Broadcast Engineering
http://www.kkbc.com
Kevin C. Kidd CSRE/AMD
WD4RAT
AM Ground Systems Company
http://www.amgroundsystems.com
KK Broadcast Engineering
http://www.kkbc.com
Re: I THINK IT IS TRYING TO TELL ME SOMETHING
I had one site where the flat roof began to leak directly into the top of a CCA AM transmitter. Water ran across the tube compartment, down the side, behind the contractors and began to pool on the cabinet floor underneath the transformers Transmitter couldn't care less, just chugged along.
<><><><><><><><><>
Chuck Gennaro
Central Wisconsin
Chuck Gennaro
Central Wisconsin
- kkiddkkidd
- Posts: 753
- Joined: Mon Dec 03, 2007 11:13 am
- Location: Lawrenceburg, TN
Re: I THINK IT IS TRYING TO TELL ME SOMETHING
Many years ago I had an HT5 where a roof vent had been installed straight over the TX exhaust... Predictably, it later leaked and boy did that HT care.ChuckG wrote: ↑Sun Jul 08, 2018 1:14 amI had one site where the flat roof began to leak directly into the top of a CCA AM transmitter. Water ran across the tube compartment, down the side, behind the contractors and began to pool on the cabinet floor underneath the transformers Transmitter couldn't care less, just chugged along.
--
Kevin C. Kidd CSRE/AMD
WD4RAT
AM Ground Systems Company
http://www.amgroundsystems.com
KK Broadcast Engineering
http://www.kkbc.com
Kevin C. Kidd CSRE/AMD
WD4RAT
AM Ground Systems Company
http://www.amgroundsystems.com
KK Broadcast Engineering
http://www.kkbc.com